Mitsubishi : CHALLENGER PB (KH) & PC Suspension Options
Vehicle Information
Make : Mitsubishi
Model : CHALLENGER PB (KH) & PC
|
Type : 4x4 SUV
Sub Type : 2008-On
|
Front Suspension : Coil Spring
|
Rear Suspension : Coil Spring
|
Vehicle Details :
Montero Sport and Pajero Sport inclusive
LBA "Load Bearing Accessories"
GVM "Gross Vehicle Mass"
|
|
Available Kits
| Kit Name |
Kit Price |
| UK-MIT-002A "Aussie Ryder" |
$1,582.50 (ea kit) |
| UK-MIT-002B + Preassembled Struts + Castor Kit |
$1,769.50 (ea kit) |
Kit Includes :
2xpr Coil Springs
2x Struts
2x Shock Absorbers
Hide Component Details
|
|
Front Suspension
Front Shock Absorber/Steering Damper Options
| Shock Absorbers |
Part Number |
Price |
| Aussie Ryder Twin Tube Gas 0-50mm |
AR74107 |
$203.50 (ea) |
|
Front Coil Spring Options
| Name |
Construction |
Price |
|
|
|
|
|
|
|
| CFR-95 |
Raised Height 0-50kg LBA 40-50mm |
$220.00 (pr) |
|
|
|
|
|
|
|
| CFR-95HD |
Raised HD 50-100kg LBA 40-50mm |
$220.00 (pr) |
|
|
|
|
|
|
|
| CFS-95 |
Standard HD 0-50kg LBA 0-20mm |
$220.00 (pr) |
|
|
|
|
|
|
|
Front Suspension Notes
NOT INCLUDED IN UK-MIT-002A
TRI-PREASSY "Pre-Assembled Struts (Uses TOPHAT-4075)"..............1x $187.00
<<< OR >>>
TOPHAT-4075 "Strut Tops (includes new top bushes and dust cover)" 2x $93.50 each
OPTIONAL
ARB145040BT "Bottom Strut Bush" ........................................................2x $24.20 each
Vehicles require wheel alignment, headlight and brake proportioning valve adjustment with raised suspension.
All raised height measurements are listed as a guide only.
|
|
Rear Suspension
Rear Shock Absorber Options
| Shock Absorbers |
Part Number |
Price |
| Aussie Ryder Twin Tube Gas 0-50mm |
AR74516C |
$160.00 (ea) |
| Aussie Ryder Twin Tube Gas 50-75mm |
AR74109 |
$160.00 (ea) |
|
Rear Coil Spring Options
| Name |
Construction |
Price |
|
|
|
|
|
|
|
| CRR-69 |
Raised Height Loads to GVM 40-50mm |
$220.00 (pr) |
|
|
|
|
|
|
|
| CRR-69HD |
Raised HD 200kg to GVM 40-50mm |
$220.00 (pr) |
|
|
|
|
|
|
|
| CRS-32 |
Raised EHD 400kg to GVM 40-50mm |
$220.00 (pr) |
|
|
|
|
|
|
|
Rear Suspension Notes
A drive-line vibration can occur between 35-40km/h when fitting Raised Height coils to the rear of this vehicle. To reduce this vibration, a Rear Castor Correction kit must be fitted.
NOT INCLUDED IN UK-MIT-002A
SPF-3861K "Rear Castor Correction Kit" ...1x $320.00
OPTIONAL
FIRESTONE AIRBAG KITS
CR5031 ...."Coil Rite - Light Loads Kit" ....1x $299.00
CR5031HP "Coil Rite - High Pressure Kit" 1x $375.00
NOTE: Compressors and On Board Air Kits are also available
Recommend Suspension Service every 12 months or 20,000km.
|
|
Special Information
- Vehicle heights may vary due to load and accessorie requirments, as a general rule a Standard Height Heavy Duty spring will raise the vehicle approx. 30mm while a Raised Height Comfort or Heavy Duty spring will raise the vehicle approx. 50mm (On a new vehicle with standard height)
- WHEEL ALIGNMENT REQUIRED
- MANDATORY 1,000KM CHECK-UP AND RE-TIGHTEN (Required under warranty conditions)
- All prices quoted are in Australian dollars, inclusive of GST. Fowarding, freight and fitting not included.
- CAUTION: Due to transort regulation in Australia, any increase in vehicle height greater than 50mm will require an engineers certificate. Check compliance with state transport Authorities
|
|
Back to the Mitsubishi List
|
|
The Ultimate Suspension
2 Noonan Road
Ingleburn NSW 2565
Ph: 02 9618 7674
Int: +612 9618 7674
Fax: 02 9603 7249
|
|
