Mitsubishi : CHALLENGER PA Suspension Options
Vehicle Information
Make : Mitsubishi
Model : CHALLENGER PA
|
Type : 4x4 SUV (SERIES II)
Sub Type : 06/00-06
|
Front Suspension : Torsion Bar
|
Rear Suspension : Coil Spring
|
Vehicle Details :
LBA "Load Bearing Accessories"
GVM "Gross Vehicle Mass"
|
|
Available Kits
| Kit Name |
Kit Price |
| UK-MIT-001 "Aussie Ryder" |
$1,322.00 (ea kit) |
Kit Includes :
2x Torsion Bars
2x Coil Springs
4x Shock Absorbers
Hide Component Details
|
|
Front Suspension
Front Shock Absorber/Steering Damper Options
| Shock Absorbers |
Part Number |
Price |
| Aussie Ryder Twin Tube Gas 0-50mm |
AR7411 |
$160.00 (ea) |
| Steering Dampers |
Part Number |
Price |
| NON Steering Damper Vehicle |
none |
P.O.A. (ea) |
|
Front Torsion Bar Options
| Name |
Construction |
Price |
|
|
|
|
|
|
|
| TB1549 |
27.5mm OD x 1307mm 0-40mm |
$231.00 (pr) |
|
|
|
|
|
|
|
Front Suspension Notes
NOTE: Replacement Torsion Bar Adjuster Bolts may be required.
Vehicles require wheel alignment, headlight and brake proportioning valve adjustment with raised suspension.
All raised height measurements are listed as a guide only.
|
|
Rear Suspension
Rear Shock Absorber Options
| Shock Absorbers |
Part Number |
Price |
| Aussie Ryder Twin Tube Gas 0-50mm |
AR74109 |
$160.00 (ea) |
|
Rear Coil Spring Options
| Name |
Construction |
Price |
|
|
|
|
|
|
|
| CRR-65 |
Raised HD Loads to GVM 40-50mm |
$110.00 (pr) |
|
|
|
|
|
|
|
| CRS-23 |
Raised HD 300kg to GVM 40-50mm |
$110.00 (pr) |
|
|
|
|
|
|
|
| CRS-65 |
Standard HD Loads to GVM 0-10mm |
$110.00 (pr) |
|
|
|
|
|
|
|
Rear Suspension Notes
OPTIONAL
FIRESTONE AIRBAG KITS
CR5007 ....."Coil Rite - Light Loads" ..........1x $349.00
CR5007HP "Coil Rite - High Pressure Kit" 1x $425.00
NOTE: Compressors and On Board Air Kits are also available
*Recommend Suspension Service every 12 months or 20,000km.
|
|
Special Information
- Vehicle heights may vary due to load and accessorie requirments, as a general rule a Standard Height Heavy Duty spring will raise the vehicle approx. 30mm while a Raised Height Comfort or Heavy Duty spring will raise the vehicle approx. 50mm (On a new vehicle with standard height)
- WHEEL ALIGNMENT REQUIRED
- MANDATORY 1,000KM CHECK-UP AND RE-TIGHTEN (Required under warranty conditions)
- All prices quoted are in Australian dollars, inclusive of GST. Fowarding, freight and fitting not included.
- CAUTION: Due to transort regulation in Australia, any increase in vehicle height greater than 50mm will require an engineers certificate. Check compliance with state transport Authorities
|
|
Back to the Mitsubishi List
|
|
The Ultimate Suspension
2 Noonan Road
Ingleburn NSW 2565
Ph: 02 9618 7674
Int: +612 9618 7674
Fax: 02 9603 7249
|
|
