Nissan : TERRANO I Suspension Options
Vehicle Information
Make : Nissan
Model : TERRANO I
|
Type : 4x4 Wagon 2 or 4 Door
Sub Type : 10/1987-1995
|
Front Suspension : Torsion Bar
|
Rear Suspension : Coil Spring
|
Vehicle Details :
Similar to;
PATHFINDER WD21
BAKKIE
TRACKER
>>><<<
LBA "Load Bearing Accessories"
GVM "Gross Vehicle Mass"
|
|
Available Kits
| Kit Name |
Kit Price |
| UK-NIS-006 Aussie Ryder |
$1,905.76 (ea kit) |
Kit Includes :
2x Torsion Bars
2x Coil Springs
4x Shock Absorbers
1x Steering Damper
Hide Component Details
|
|
Front Suspension
Front Shock Absorber/Steering Damper Options
| Shock Absorbers |
Part Number |
Price |
| Aussie Ryder Twin Tube Gas 0-50mm |
AR7411 |
$203.50 (ea) |
| Steering Dampers |
Part Number |
Price |
| Gibson Ryder Foam Cell |
GR13826 |
$137.50 (ea) |
|
Front Torsion Bar Options
| Name |
Construction |
Price |
|
|
|
|
|
|
|
| TB1458 |
26mm OD x 1232mm 0-40mm |
$231.00 (pr) |
|
|
|
|
|
|
|
Front Suspension Notes
NOTE: Replacement torsion bar adjuster bolts may be required.
SUSPENSION BUSHES (not included in kit)
SPF0658K ......"Upper Bump Stop" ...........................................................................1x $27.50
SPF0148K ......"Control Arm Lower- Rear 4WD- strut bar style mount" ......................1x $82.50
SPF2151K ......"Control Arm Lower- Front Must re-use original shell" ............................1x $85.50
SPF0879K ......"Control Arm Upper- Inner" ..................................................................1x $88.00
RRW-720 ........."Strut Bar Mount Repair Washers Must be welded on over original hole" 1x $44.00
SPF2092B-4K "Sway Bar Link Bushing" .....................................................................1x $21.50
SPS0900-__K "Sway Bar Mount Bushing *Measure Sway bar" ..................................1x $27.50
Vehicles require Wheel Alignment, Headlight and Brake Proportioning Valve adjustment with raised suspension.
All raised height measurements are listed as a guide only.
|
|
Rear Suspension
Rear Shock Absorber Options
| Shock Absorbers |
Part Number |
Price |
| Aussie Ryder Twin Tube Gas 0-50mm |
AR74523 |
$160.00 (ea) |
|
Rear Coil Spring Options
| Name |
Construction |
Price |
|
|
|
|
|
|
|
| *DRR-30 SWB |
Raised Height Loads to GVM 40-50mm |
$110.00 (pr) |
|
|
|
|
|
|
|
| *DRR-30HD SWD |
Raised HD 300kg to GVM 40-50mm |
$110.00 (pr) |
|
|
|
|
|
|
|
| DRR-30 LWB |
Standard HD Loads to GVM 0-20mm |
$110.00 (pr) |
|
|
|
|
|
|
|
| DRR-30HD LWB |
Raised Height Loads to GVM 40-50mm |
$110.00 (pr) |
|
|
|
|
|
|
|
| DRS-30EHD LWB |
Raised HD 300kg to GVM 40-50mm |
$110.00 (pr) |
|
|
|
|
|
|
|
Rear Suspension Notes
FIRESTONE AIRBAG KIT (not included in kit)
CR5022 "Coil Rite" 1x $299.00
CR5022HP "Coil Rite High Pressure" 1x $375.00
NOTE: Compressors and On Board Air Kits are also available
*Recommend Suspension Service every 12 months or 20,000km.
|
|
Special Information
- Vehicle heights may vary due to load and accessorie requirments, as a general rule a Standard Height Heavy Duty spring will raise the vehicle approx. 30mm while a Raised Height Comfort or Heavy Duty spring will raise the vehicle approx. 50mm (On a new vehicle with standard height)
- WHEEL ALIGNMENT REQUIRED
- MANDATORY 1,000KM CHECK-UP AND RE-TIGHTEN (Required under warranty conditions)
- All prices quoted are in Australian dollars, inclusive of GST. Fowarding, freight and fitting not included.
- CAUTION: Due to transort regulation in Australia, any increase in vehicle height greater than 50mm will require an engineers certificate. Check compliance with state transport Authorities
|
|
Back to the Nissan List
|
|
The Ultimate Suspension
2 Noonan Road
Ingleburn NSW 2565
Ph: 02 9618 7674
Int: +612 9618 7674
Fax: 02 9603 7249
|
|
